工业滑升门由一系列门板组成（常见的为金属或布质材料等），沿轨道上升，工业滑升门在外观结构设计气派、使用舒畅之感；而较大尺寸的工业产品其稳定、壮观的运行态势更能带给人们强烈的视觉冲击。由扭簧系统或配重系统来保障门体平衡，轨道系统和提升方式的不同工业提升门板使其能适应不同的建筑，多种颜色可供选择。它灵巧的特点使其几乎能适合每一种建筑物外的用门。
工业滑升门的安装注意事项：
一、钢架的安装：用标准规格的钢架立于洞口的两侧，保证钢架的垂直度和水平度，然后用10个m10×110㎜的膨胀螺栓固定到墙壁上，保证每个点能承受1000n的垂直拉力而不脱落、不松动，并注意避开轨道固定件的安装位置。
二、轨道的安装：根据工业滑升门的门板宽度和高度确定两轨道固定件的位置并用水平管测水平，再用m8×41㎜的方头螺钉固定。
三、扭簧的安装：将扭簧中心支架、尼龙胶圈固定法兰、与门体重量相匹配的扭簧、锁紧法兰、绕线轮、轴承支架按顺序（分清左右侧）套在镀锌钢管上，并注意各零部件是否安装正确。
四、工业滑升门门板的安装：将底密封条放到底门板的底部，并用m4×16㎜或m6.4×16㎜的自攻钉将其从背面固定到门板上。
五、调整：用手将工业提升门升降数次，观察门体运行是否平稳，扭簧的力量是否适当，然后做具体调整并紧固各连接部分的螺丝。
六、工业滑升门电机的安装：将链盒与电机连接并固定。将链盒前端的u形架固定到扭簧中心支架上面的木板上并居中，连接链盒。用带眼角钢做成“∏”支架，下端与电机用m8连接固定，上端用两个m8×70㎜的膨胀螺栓固定到天棚上。用m6.4×16㎜的自攻钉将钩座固定到顶门板顶部的中间位置上，连接钩子。接上电源，观察电机的运行情况，调整上下行程。
七、布线：用φ1.0线径的白色护套线，从电机尾部的电动开关接线端子中引出，顺着电机吊架布到洞口左侧距地面1.2m处，每隔500㎜钉一个线卡子，然后接上手动开关。布线要横平竖直，既美观又合理。
八、提手的安装：提手应安装在底门板上，左右居中，横向中心线与方格的下端边缘线对齐。
九、锁的安装：锁眼应用专门的开孔器，开在从下往上数的第三块门板的中心位置，安装时锁槽一律向下，背帽拧紧。
产品英文详情介绍
industrial sliding door consisting of a door panel consists of a series (or a common cloth material, a metal, etc.), rises along the track, industrial sliding doors appearance design style, comfortable feeling used; the larger size of its stable industrial products, spectacular running posture better to bring people a strong visual impact. to protect the system by the torsion spring or counterweight balanced door systems, rail systems and different ways to enhance industrial lifting door so that it can adapt to different buildings, a variety of colors to choose from. it's smart features make it suitable for almost outside the door of each building. industrial sliding doors installation notes: a steel frame mounted: a standard steel stand on both sides of the hole, to ensure that the degree of vertical and horizontal steel frame, and then the expansion bolt 10 of the m10 脳 110 mm to a wall, to ensure that each point to withstand the vertical force of 1000n and not fall off, not loose, and note the position of the track to avoid the mounting fixture. second, the mounting rail: determining the position of two rail fixing device according to industrial sliding doors and the door width and height of the horizontal pipe test level, then the square head screws m8 脳 41銕 third, the torsion spring installed: the center of the torsion spring bracket, nylon apron fastening flange, to match the weight of the door of the torsion spring, locking flange, the reel, the bearing support sequentially (to distinguish between left and right sides) in the sleeve galvanized steel pipe, and note that all parts are installed correctly. fourth, industrial sliding doors mounted door: the door in the end of the discharge end of the bottom sealing strip, and with m4 脳 16 mm or 16 mm m6.4 脳 self-tapping screw which is fixed to the door panel from the back side. v. adjustment: hand industrial doors down several times, to observe whether the door is running smoothly, the torsion spring force is appropriate, and then tighten the screws to make specific adjustments and the respective connecting portions. 6, installation of industrial sliding door motor: the motor is connected with the chain case and fixed. the front end of the chain case u-shaped frame is fixed to the frame above the center of the torsion spring plank and centered, connection chain case. 螤 bracket, with the lower end of the motor m8 is connected to the fixing belt made of steel corner, the upper end is bolted to the ceiling with two expansion of m8 脳 70 mm. m6.4 脳 16 mm with a self-tapping screw fixing the hook base to the top of the door on the middle of the top, connected to a hook. plugged in to observe the operation of the motor, to adjust the vertical stroke. , wiring: white sheath wire diameter of 蠁1.0, drawn from the electric motor end of the switch terminals, the motor down to the left side cloth hanger hole at 1.2m from the ground, a staple line every 500 mm clips, and then connected to a manual switch. to smooth vertical and horizontal line, both beautiful and reasonable. eight, the installation handle: the handle should be mounted on the bottom of the door panel, around the center, the lower end of the transverse centerline and edge line grid alignment. ix lock installation: a dedicated application keyhole opening, open at the central position of the third block from the number of door panel up, when installing the lock groove all down, the cap screwed back.
非瑞普（苏州）智能设备有限公司
18662659657
